Please sign in to view pricing and place orders online.

The Veneer Reference

11/18/2026

Wood Veneer Glossary & Reference Guide
Herzog VeneersVisit VeneerOnline.com ↗

Get to know the cuts, figures, and matching methods that bring wood veneer to life. Explore the illustrations below and find the right language for your next project.

26 illustrated terms · 3 reference categories

Veneer cuts

Back to top ↑

How a log meets the knife determines the grain pattern of each veneer leaf.

Flat Cut / Plain Sliced — slicing diagram

Flat Cut / Plain Sliced

Defined by a cathedral or heart

Half a log is mounted on a large steel rack which moves up and down through a stationary knife through a series of vertical, parallel cuts. This produces consecutive leaves of veneer with the standard appearance of veneer (the "cathedral" or flame-shaped arch). When a log is flat cut it will generate flat cut bundles. As you get to the center of the log, normally the rest of the flitch is split open to produce a quartered look called flat cut quarters.

Quarter Cut — slicing diagram

Quarter Cut

Straight grain or ribbon-striped appearance

A quarter of the log is mounted off center so that the growth rings strike the knife at a right angle. The edge of the annual rings create the lineal figure of the veneer. Quartered leaves cut consecutively are narrower than plain sliced and typically contain straighter grain. Some flake is produced when cutting through the medullary rays, especially in Oak.

Rotary Cut — slicing diagram

Rotary Cut

Creates a bold sometimes wild, variated grain

An entire log is mounted so that the log turns on its long axis. While spinning, the knife advances toward the center of the log slicing or peeling a continuous sheet of veneer. Sometimes a score line is cut into the log to give the effect of consecutive sheets. This is especially true of burls and Bird's Eye Maple.

Rift Cut — slicing diagram

Rift Cut

A straight grain effect similar to true quarter cut veneer

Used in Oak to minimize the "flake" effect, the cant is cut at an angle of 15 degrees off the quartered position.

Half Round Slicing — slicing diagram

Half Round Slicing

Modified characteristics of both rotary and flat cut veneers

A half of a log is mounted so that it will cause the blade to cut slightly across the growth rings. This is primarily used to accentuate the grain in various woods such as in burls or Bird's Eye Maple, or to gain a wider width on a cathedral on small dimension logs.

Wood figures

Back to top ↑

Figure describes the natural patterns and visual effects within the wood. Play the animations to see how figured veneer changes in the light.

Bird's Eye — wood veneer figure

Bird's Eye

Characterized by its scattered circles or ovals that have a similar appearance to that of a bird's eye. This type of figure is found almost exclusively in Hard Maple.

Burl / Burr Veneer — wood veneer figure

Burl / Burr Veneer

Veneer obtained from rare woody outgrowths appearing on trees around grafts or injuries. This produces an appearance of a close arrangement of many small eyes or knots intermingled with distorted grain. The unusual patterns of burls make them in high demand but also more expensive due to their small size and scarcity.

Crossfire — wood veneer figure

Crossfire

This term is used to describe all of the various figure marks running perpendicular to the veneer grain. In some wood species the crossfire is a contrast of color, while others appear as an irregularity of the grain creating the illusion of horizontal marks.

Crotchwood — wood veneer figure

Crotchwood

This type of figure occurs where limbs emerge from the tree trunk. The high amounts of fiber distortion at this junction results in a feather or flame pattern appearance. Mahogany is the most common species with this type of figuring.

Curly — wood veneer figure

Curly

The term used for a wavy or curly figuring produced by distorted fiber growth that reflects light differently. Most commonly available in Walnut and Maple veneers. This figure has high chatoyancy: a shimmering effect that changes with the viewing angle and direction of light.

Fiddleback — wood veneer figure

Fiddleback

A term describing consistent ripple figure running across the grain. Fiddleback is not commonly found but occasionally occurs in Mahogany, English Sycamore, and Anegre. The term fiddleback comes from the veneer's popularity in making violin backs. This figure has high chatoyancy: a shimmering effect that changes with the viewing angle and direction of light.

Flake — wood veneer figure

Flake

This is found only in species that have prominent medullary rays (cells radiating outward from the center of the tree, like the spokes of a wheel.) By slicing the veneer perpendicular to the annual rings and parallel with the rays, a distinctive "flake" within the figure is created.

Mottle — wood veneer figure

Mottle

Mottle is the intermingling of broken cross markings with stripe figure. Block mottle involves broad cross markings producing a patch effect and is commonly found in Makore. Bees-wing-mottle is very small, fine figure and often occurs in Sapele, Satinwood and Black Bean.

Plain Stripe and Ribbon Stripe — wood veneer figure

Plain Stripe and Ribbon Stripe

The figure is straight and parallel with the length of veneer as a result of quarter slicing the log. Ribbon stripe is similar but with variable width bands, alternating light and dark, that create the appearance of ribbons.

Peanut Shell — wood veneer figure

Peanut Shell

A quilted or blistered figure that incorporates a dominant grain or growth-ring pattern. Mostly found in Tamo or Bubinga.

Pommele — wood veneer figure

Pommele

Pommele gets its name from the French word for "apple." The figure resembles small round or oval circles that can overlap each other. Sometimes a log that has larger and more sparsely occurring "apples" can be referred to as blistered. This figure has high chatoyancy: a shimmering effect that changes with the viewing angle and direction of light.

Quilted — wood veneer figure

Quilted

This figuring is produced by rotary or half-round slicing of logs that have a "bumpy" surface. The uneven weaving of the growth rings produces a quilted, three-dimensional effect. Maple and Mahogany are species often available with quilted figure.

Recon Oak MN208 Quarter Cut Plain — recomposed veneer

Recomposed or Man-made Veneers

These veneers are sliced from man-made "cants" that have been laminated, or resliced, to produce distinctive figures or patterns.

Veneer matches

Back to top ↑

Matching describes how veneer leaves are arranged to create a finished panel.

Balance Match — veneer arrangement

Balance Match

The width of each veneer leaf in a panel is the same, but there can be any number of leaves.

Book Match — veneer arrangement

Book Match

Every other leaf is turned over like the pages in a book. This is the most popular matching method and creates a symmetrical pattern and a series of pairs.

Book & Butt Match — veneer arrangement

Book & Butt Match

The veneer is joined end to end and side to side. This is sometimes used when the veneer is not long enough to cover the desired panel height. It is also a popular method for burls, crotches, and highly decorative veneers.

Center Match — veneer arrangement

Center Match

Each face has an even number of veneer sheets, but the widths are not necessarily the same. The center joint will be in the middle of the panel.

Diamond or Box Match — veneer arrangement

Diamond or Box Match

Four equal pieces of veneer are cut diagonally to the usually straight grain. These are matched to create a diamond pattern. In a reverse diamond match, the pieces are matched so that the grain direction runs toward the middle.

Random Match — veneer arrangement

Random Match

Deliberate mismatched leaves are placed next to each other to give a rustic, natural look. This works especially well with knotty or wormy species.

Slip Match — veneer arrangement

Slip Match

Consecutive sheets are slipped out in sequence to expose the same side of veneer and a repeating grain figure. The result is a series of grain repeats, but no pairs.

Sunburst Match — veneer arrangement

Sunburst Match

Consecutive sheets are trimmed into pie shaped pieces and matched in a circular fashion in which the points meet in the center. Mostly used on round, oval or octagonal shaped panels.

Conversion chart

Back to top ↑

A quick reference for veneer thickness and other small measurements. One inch equals 25.4 millimeters.

Inches to millimeters
Fractional inchesDecimal inchesThousandths of an inchMillimeters (mm)
—0.00393.90.100
—0.00797.90.200
—0.011811.80.300
1/640.015615.60.397
—0.015715.70.400
1/500.020020.00.508
—0.023623.60.600
—0.027627.60.700
1/320.031231.20.794
—0.031531.50.800
—0.035435.40.900
—0.039439.41.000
—0.043343.31.100
3/640.046946.91.191
—0.047247.21.200
—0.051251.21.300
—0.055155.11.400
—0.059159.11.500
1/160.062562.51.587
—0.063063.01.600
—0.066966.91.700
—0.070970.91.800
—0.074874.81.900
5/640.078178.11.984
—0.078778.72.000
—0.082782.72.100
—0.086686.62.200
—0.090690.62.300
3/320.093893.82.381
—0.094594.52.400
—0.098498.42.500
7/640.1094109.42.778
—0.1181118.13.000
1/80.1250125.03.175

Values are rounded. Fractional references are shown where applicable; a dash indicates a metric reference without a listed fraction.

Herzog Veneers · Established 1982 · High Point, North Carolina